Small (small inground or above-ground surround)
Up to ~300 sq ft
From
$1,800
to $5,800
- Above-ground pool decks and small inground surrounds
- Ultimate tier standard
Pool Deck Coating · Burnsville, MN · Est. 1996
Pool Deck Coating in Burnsville, Minnesota.
Burnsville sits on the south side of the Minnesota River across from Bloomington, a Dakota County city of more than 64,000. It grew earlier than its neighbors to the south, so its housing is a full generation older than Lakeville's. Pool deck coating for Burnsville homes. Aggregate-textured polyaspartic topcoats for wet-surface grip, light color options to reduce heat absorption, full prep including any chlorinated-area concrete damage. Burnsville is the mirror image of Lakeville. The bulk of the stock went up in the 1970s and 1980s: split-levels, ramblers and two-story colonials with 2-car attached garages as the standard, on slabs that are now forty to fifty years old. A 1990s layer sits around the edges, and the Heart of the City redevelopment added newer multi-family and townhomes near the center. Three-car garages exist but are the exception rather than the rule. That age profile means Burnsville estimates involve more prep and more honest assessment than the newer suburbs do.
Pool Deck Coating in Burnsville
What an install looks like in Burnsville.
Burnsville is where the prep work matters. Most of the city's garages were poured in the 1970s and 1980s, which means the slabs have taken forty-plus winters of salt off three highway corridors and, in a lot of cases, a coat of hardware-store epoxy somewhere along the way that is now lifting in sheets where the tires sit. That is a heavier grind than a Lakeville or Savage floor, and it changes the quote. It is also the situation where a proper polyurea system makes the biggest visible difference, because the starting point is so much worse. The kitchens tell the same story: 1980s and 1990s stone that has never been professionally restored.
Pool Deck Coating specifically in Burnsville
In-ground pools in Burnsville are mostly in the larger-lot 1980s neighborhoods near Crystal Lake and Alimagnet. The decks are as old as the pools, so the project usually starts with surface repair before the Apex tier goes down with slip-resistant aggregate broadcast. Chlorine-tolerant, UV-stable, cooler underfoot than bare concrete. Installs schedule May through early September.
Neighborhoods we work in
- Heart of the City
- Crystal Lake
- Sunset Pond
- Alimagnet
- Terrace Oaks
- Cliff Fen
Slip
Resistant
Aggregate added to topcoat
UV
Stable
Polyaspartic topcoat
Cl
Tolerant
Chlorinated water + salt OK
A+
BBB rated
Accredited since October 2005
Why pool decks need their own spec in Burnsville
What makes a pool deck coating different from a patio coating.
Three things: slip resistance, heat reflectivity, and chemical exposure. A pool deck coating without all three is a patio coating in the wrong context. Aggregate in the topcoat handles grip. Light color reflects heat for barefoot comfort. UV-stable, chlorine-tolerant chemistry handles the chemical side. We don't shortcut any of the three.
Burnsville Pricing
Pool deck coating pricing in Burnsville, MN.
Pool deck pricing tracks square footage and prep complexity. Concrete near pools sometimes has settling, efflorescence from chlorinated water, or surface damage from years of pool chemicals; all that gets addressed during prep.
Standard (inground residential)
~400 to 700 sq ft
From
$3,400
to $9,000
- Most residential inground pool decks
- Ultimate with grip aggregate is the standard pick
Large or premium
800+ sq ft
From
$5,000
to $14,400+
- Large pool surrounds, outdoor entertainment areas
- Apex for older slabs with cracking
Pool deck installs schedule around the pool-open season. We can install over the spring opening window or in fall after closing; both work better than mid-summer for cure conditions.
The 6-step install
How we install your floor in Burnsville.
Pool deck prep is more involved than a normal patio because of the water exposure history. Same checklist, scaled to the conditions.
- 1
On-site assessment + written quote
Visit, measure the deck, evaluate existing condition including any chlorine-exposure damage, write a fixed quote. - 2
Cover the pool + protect surrounding plantings
Pool surface covered to keep prep dust and coating material out. Plantings and any features near the deck masked or covered. - 3
Diamond-ground prep + crack repair
Full surface prep, crack filling, edge repair near the pool waterline if needed. - 4
Basecoat application
Polyurea or flexible urethane basecoat depending on tier, rolled and back-rolled. - 5
Decorative flake + aggregate topcoat
Decorative flake broadcast into wet basecoat. After cure, scraped flat. Polyaspartic topcoat with grip aggregate broadcast in for slip resistance. - 6
Walk-through + cure
Final walk-through. Walkable in 24 hours, fully cured for swim use in 48.
Burnsville questions
Common questions for Burnsville homeowners.
My Burnsville garage has old epoxy peeling off in sheets. Can you still coat it?
Yes, and it is one of the most common Burnsville projects. Failed hardware-store epoxy has to come off completely before anything goes down, which is what diamond grinding is for. Once the slab is ground back to clean concrete and the pits and joints are repaired, a polyurea basecoat bonds properly in a way the original coating never did. The peeling is a symptom of bad prep the first time, not a reason the floor cannot be coated.
Is a 1978 Burnsville garage slab worth coating or should it be replaced?
Almost always worth coating. Most slabs from that era are structurally sound underneath; what looks bad is surface damage, salt pitting near the door, hot-tire pickup and hairline cracking. All three are prep problems, not concrete problems. If a slab genuinely has settled, cracked beyond hairline or spalled deeply, we say so at the in-home assessment and point you to a concrete contractor rather than putting a finished surface over a failing one.
Does the extra prep on an older slab cost more?
It can, and it is written into the quote at the in-home estimate rather than added later. A slab with failed coating to remove and pitting to repair takes more grinding time and more repair material than a fifteen-year-old slab in Savage does. You will see that in the number before you agree to anything. The system that goes down on top is the same either way.
Do you cover the whole city, including the older neighborhoods near Crystal Lake?
Yes, all of Burnsville. Twenty miles, roughly thirty minutes via Hwy 13, on the standard service area with no travel adjustment. The older neighborhoods are where the most dramatic before-and-after results come from, because the starting condition is furthest from where it ends up.
Will it actually be slip resistant when wet?
Yes. The polyaspartic topcoat is broadcast with grip aggregate (fine silica or polymer beads, depending on the texture level you want) that gives bare feet traction on a wet surface. Aggressive enough for safety, fine enough not to be uncomfortable.
Will it get hot in the sun?
Light color choices reflect significantly more heat than dark ones. We recommend lighter flake blends for pool decks specifically for this reason. Not as cool as some specialty acrylic pool deck coatings, but far cooler than dark stained concrete.
Does chlorine damage the coating?
Polyaspartic is chlorine tolerant at normal pool concentrations. Saltwater pool systems are also fine. Heavy chemical spills (concentrated shock, muriatic acid) should still be rinsed off promptly, same as you would for any finished surface.
What about the pool coping or waterline edge?
We coat the horizontal deck surface. The vertical pool coping (stone or concrete cap at the waterline) is a separate decision; we can talk through whether to include it during the estimate.
Can I coat a concrete deck with a stamped pattern?
Film coatings cover stamped patterns. If you want to keep the decorative pattern, the Essential sealer (also offered) preserves the look while adding chlorine and freeze-thaw protection.
How long does the install take?
Most residential pool decks are 1 to 2 days on site. Larger or premium decks take longer. We coordinate around the pool-use season; spring or fall installs are easier than mid-summer.
When can I open the pool after the install?
48 hours for walk and swim use. Full coating cure continues for a week beyond that, but the surface is functionally ready at 48.
Do you offer a warranty?
Yes. Written limited warranty, terms vary by tier, walked through during the estimate.
More in Burnsville
All the services we offer in Burnsville, MN.
Pool deck plus surrounding patio is a common combined install. Same prep and chemistry; we can size the visit to do both.
Restoration in Burnsville
Other surfaces we work on in Burnsville.
Clear View runs both sides of the business out of the same shop. If you're booking a pool deck coating in Burnsville, bundle pricing applies when we restore or coat another surface in the same visit.
Pool Deck Coating elsewhere
Pool Deck Coating in nearby cities.
Same UV + chlorine-tolerant systems across the metro. If you're outside {city}, here's where else we work.
- Pool Deck Coating in Chaska, MN
- Pool Deck Coating in Chanhassen, MN
- Pool Deck Coating in Eden Prairie, MN
- Pool Deck Coating in Bloomington, MN
- Pool Deck Coating in Edina, MN
- Pool Deck Coating in Minnetonka, MN
- Pool Deck Coating in Shakopee, MN
- Pool Deck Coating in Prior Lake, MN
- Pool Deck Coating in Waconia, MN
- Pool Deck Coating in Victoria, MN
- Pool Deck Coating in Plymouth, MN
- Pool Deck Coating in Excelsior, MN
- Pool Deck Coating in Minnetrista, MN
Get a quote
Ready for a pool deck coating install in Burnsville?
Tell us about your pool deck. We'll get back with quote details for Burnsville within one business day.
- Free on-site measurement
- Written limited warranty
- No subcontractors, no upsells